Adaptateur Alimentation SATA - 323104
Connectic Systems
Distributeur Belkin Ovislink Logitech Hdmi
Compte Panier Suivi Commande


Arduino - 749031
Préchargement des images de survol
Bienvenue visiteur
Exemple de Recherche :
1 - avec un ou plusieurs mots : mot1 mot2
2 - Recherche avec deux mots maximum
et le séparateur "ou" : mot1 ou mot2
Tapez un mot-clé ou une référence :
Les tutoriels vidéos sur Youtube Tout le Catalogue 2020 Les nouveautés Tous les connecteurs en images La Connectique Vidéo Les bonnes affaires & Occasions
Votre panier est vide actuellement
Suivi de commande
Suivez l'état de vos commandes
Pour commander, c'est facile ! Livraison Conditions générales de vente SAV & Retour de marchandises Foire aux Questions Liens utiles & Partenaires
Contact & Infos Société Nous envoyer un message Plan d'accès au magasin
Connectic Systems
51 avenue de L'U.R.S.S.
31400 Toulouse

Tél :
Le magasin est ouvert
du lundi au vendredi
de 10h00 à 12h30
et de 16h00 à 18h30

Siret : 492.382.155.00025
APE : 2640Z
N° TVA INTRACEE : FR 19 492382155

Vente aux particuliers,
professionnels, administrations,
établissements scolaires, etc...

Toutes les marques citées sont la propriété de leur déposant respectif.
Les photos ne sont pas contractuelles.
Les prix sont modifiables sans préavis.
Sous réserve de toutes erreurs typographiques.

La disponibilité et les délais sont modifiables sans préavis en fonction du stock et de la charge de travail.

Ce site n'utilise pas les cookies
que ce soit en dépôt ou en lecture,
ni aucun système de traçage.

Tous droits réservés 1984-2020
Copyright Connectic Systems
Mise à jour le 12.10.2020
Résultat de la recherche : 1 article


Outillage - 855200
Référence : 855200

29.90 € ttc


Original JYETech DSO-SHELL DSO150 15001K DIY Digital Oscilloscope Kit à monter
DSO Shell (DSO150) Oscilloscope DIY Kit:

1. DSO Shell has similar bandwitch as DSO138 though it contains significant improvements in structure, mechanical, and operation.
2. Display and MCU are now mounted on the same board (mainboard) to avoid using inter-board pin-headers. Feedback from DSO138 usres have shown that soldering on the pin-headers are often problematic for many beginners. Analog channel is placed on a separated board which contains most user install parts. This brings in better separation between analog and digital circuits. Without the analog portion the mainboard is actually a general purpose control board that can be used in many other applications. The mainboard is fully installed (except a few through-hold components) and factory tested before packing.
3. DSO Shell comes with full enclosure. The front panel and top/bottom brackets are flexiable for easy user modification.
4. Rotary encoder has been added. It makes parameter adjustment much quicker and easier.
5. The sensitivity of DSO Shell has been extended in both directions and is higher and wider than DSO138. It reaches 5mV/div --- 20V/div while DSO138 is only 10mV/div --- 5V/div.
6. DSO Shell runs on 9V (do not use power voltage higher than 10V!) power supply. Users need to prepare their own power supply since it is not included in the kits. The power jack on the mainboard accepts standare 5.5mm/2.1mm DC plug. Alternative 2-pin connector (0.1" pitch) is also provided for convenience to connect to different power sources.

Important Notes:

It is assumed that users have adaquate soldering skills and troubleshooting skills to assemble the DSO Shell kits. Buyers are advised that due to skills of user is involved in assembly it is not guaranteed every kit will end up being a working device. But we will make as much efforts as we can to approach that goal.
After receiving the kits users are urged to check mainboard and LCD by applying proper power supply. Report immediately to us or JYE Tech if problem or damage is found.

Characteristics of indicators:

Number of channel: 1
Analog bandwidth: 0 - 200KHz
Sensitivity: 5mV/Div - 20V/Div
Sensitivity error: < 5%
Resolution: 12-bit
Input Impedance: 1M ohm
Maximum input voltage: 50Vpk
Coupling: DC, AC, GND
Max real-time sampling rate: 1Msps
Timebase: 10us/Div - 500s/Div
Record length: 1024
Trigger modes: Auto, Normal, Single
Trigger types: Rising/falling edge
Trigger position: 1/2 of buffer size fixed
2.4-inch color TFT LCD with 320 x 240 resolution
Power supply: 9V DC (please make sure the power supply is 9V, lower or higher than 9V will cause problems.)
Supply current: 120mA @ 9V
Dimension: 115mm x 75mm x 22mm
Weight: 100 gram (not including cables and power supply)

Update informations: Component accessories and PCB board made a number of changes
Firmwares: Click to open
Users Manual: Click to open
Mainboard Schematic: Click to open
Analog board Schematic: Click to open
How to Use the DSO150 Library: Click to open
Source codes: Click to open
FAQ, Tips, and Troubleshooting: Click to open

Package includes:

1 x DIY DSO150 Digital Oscilloscope Kit (There may be a color difference)
1 x EN Instruction